M22520/1-01 Standard Adjustable Indent Crimp Tool

AF8

  • 12 - 26 AWG Wire Range
  • Qualified to MIL-DTL-22520/1 and AS22520/1
  • Accommodates Daniels single and multiple position turret heads

Your Price

$313.42

2150 In Stock

Register/Login for purchase options

The DMC AF8, qualified to MIL-DTL-22520/1* and AS22520/1*, has virtually limitless application within the specified wire range of 12 through 26 AWG. Over a thousand turret heads are available to adapt the tool frame to your specific military or proprietary contact/wire combination. The 8 impression crimp, which is standard in the AF8, assures absolute maximum tensile strength with almost every closed barrel contact. Special indent configurations and gaging are available upon request.

 

For proper operation, the tool must be mated with one of the following optional accessories: a military standard or non-military turret head (TH-XXX Part No. Series), a military standard or non-military positioner (TP-XXX Part No. Series), or an adjustable head (Part No. UH2-5). This is done simply by orienting the head in the keyed position, and by tightening the hex socket screws provided as part of the head.

 

The precision ratchet controls cycling of the tool in both directions of handle movement. This assures the same accurate crimp every time. It's like having a quality control inspector at every work station.Positive crimp depth is controlled by an 8 position selector knob conveniently located on the tool frame. The operator simply dials the desired step for the wire being used. This setting can be secured by use of a locking pin or safety wire.

 

A permanent dataplate is affixed to all turret heads and positioners. This plate lists specific contact part numbers, the corresponding position color code (for 3 position turret heads), and suggested selector depth settings for the wire size being used.

 

The AF8 is approximately 9.75" x 2.5" x 1.25" and weighs 15 oz.

 

Periodic gaging is recommended to insure accurate calibration. This can be done easily by setting the tool selector knob to position #4, and checking indenter closure with the M22520/3-1 Go/No-Go gage (DMC part no. G125).  For a complete set of non-Mil-Spec Go/No Go gages for all selector settings, see DMC part no. 88-100.

 

Other than keeping the unit clean and properly stored when not in service, no operator maintenance is required. DMC offers complete factory service by knowledgeable technicians within a reasonable turnaround time. Complete instructions concerning the use, care and warranty are supplied with each tool. 

 

The battery powered versions of this tool is the AFE8B.

 

The pneumatic versions of this tool is the WA27F.

 

The DMC1186 tool kit contains the AF8 tool frame, tool gage, and all mil-spec positioners and turret heads. 

 

For a complete listing of AS22520 to DMC Tooling, please click here.

Specification Value
Weight 1.25 LBS
Military Part Number M22520/1-01
National Stocking Number 5120013358571
National Stocking Number 5120001653912

Limited Warranty / Limitation of Liability*

Daniels Manufacturing Corporation warrants each new unit sold by it to be free from defects in material and workmanship under normal use and service. DMC’s obligation under this warranty is limited to the free correction or, at DMC’s option, the refund of the purchase price of any such unit which proves defective within Ninety (90) Days after delivery to the first user, provided that the unit is returned to DMC with all transportation charges prepaid, and which shall appear to DMC’s satisfaction, upon inspection by DMC, to have been defective in material or workmanship.

This warranty shall not cover any damage to such products, which in the opinion of Daniels Manufacturing Corporation, was caused by normal wear, misuse, improper operation or accident. This warranty is in lieu of all other warranties express or implied. No warranty express or implied, is made or authorized to be made or assumed with respect to products of Daniels Manufacturing Corporation, other than those herein set forth. The tooling suggested within this website may not cover a user's specific contract or manufacturing requirements. It is the user's responsibility to carry out sufficient testing to verify the suitability of the DMC product selected for the specific requirements of each particular application. DMC is not liable for consequential or special damages of any nature or kind resulting from the use of any of our products. Daniels Manufacturing Corporation is not liable for Consequential or Special Damages of any nature or kind resulting from the use of any of its products. Owners and users of DMC products assume full responsibility for instructing their employees in the proper and safe use of such products. *as defined by PL93-637.

 

Returns

Materials to be returned for exchange or credit must have prior authorization from Daniels Manufacturing Corporation (DMC) in the form of the issuance of a Return Material Authorization (RMA) control number. DMC, at its sole discretion, will determine if an RMA will be issued.

 

To obtain an RMA, please contact our Sales Department at 407-855-6161 or sales@dmctools.com.

Material returned must be standard items produced by DMC, unused, in saleable condition and not more than three (3) months old. Special order or custom made items are not returnable.

 

Return material will be subject to a re-stocking charge up to twenty percent (20%). 

 

RMA's for kits are subject to a twenty percent (20%) to forty (40%) re-stocking charge if the kit is returnable.

 

Return credit must be offset by a purchase order for new DMC product on a dollar for dollar basis.